Home-Tech

Connect shower drain to toilet drain in 4 easy steps; Check how it functions

Connect shower drain to toilet drain: The problem of a shower drain and toilet draining into the same pipe is not as rare as one would hope. This blog post will give you some tips on how to connect your shower drain to toilet drain, and save yourself from clogs and costly plumbing bills in the future.

This article provides different methods that can be used for this type of job, including the use of PVC piping, ABS plastic pipe or cast-iron plumbing. Each has its pros and cons that are outlined in the article to help you make your decision on which material is best for your needs.

Connect shower drain to toilet drain

While it may seem like a daunting task at first glance, connecting the shower drain to the toilet drain can be quite simple if you did properly. You require to know about how to cut out the old PVC piping, how to use re-using an existing 3 inch ABS or PVC pipe, how to use flexible drainage tubes with flare fittings at either end, how to use using a Y connector with 2 inch ABS or PVC pipes connected at their ends, how installing a wall trap (a U-shaped bend) with rigid 4 inch ABS or PVC pipe installed vertically on both sides.

How to cut out the old PVC piping?

This is done by first making sure all the water is turned off to prevent injury. A plumber will use a saw to disconnect the pipe where it attaches to the threaded fitting, and then remove it with a pair of pincers or with his hands. The plumber may opt to use an air chisel; this is especially helpful if there’s no one home and he needs to go fast (or need access into tight spots).

He’ll start by drilling a small hole through the PVC pipe about two inches from its end, and blasting away with compressed air until one inch of PVC casing remains. Once again inserted through the hole at about four feet per minute (fpm) without stopping. Finally, he will finish the job.

How to run Romex in the attic in 3 easy ways which are really effective

How to re-use an existing 3 inch ABS or PVC pipe?

Answer: To reuse an existing 3″ ABS or PVC pipe, first you must know what the inside circumference of the pipe is from end to end. You will need a piece of wire that has a circular dial on it as well as a metal ruler with both millimetres and inches. Measure down from one endpoint of the pipe on either side and mark each spot with string then wrap around on that spot where you measure your open circle dials up to match your measuring increments.

Next compress this middle segment together, overlapping the two wires overlapping them on top of one another for a second before lowering back down to form loops so they can be tightened together by hand until they meet in the centre. Finally, your job will conclude.

How to use a Y connector with 2 inch ABS or PVC pipes

This Y fitting is not like the one you will see on a sink where two pipes join. If you are using 2 inch ABS or PVC pipe, this Y connector is the best option to use.

First, use a T-fitting to put one side of your piping system in place then attach your Y connector. From there connect that outlet to another length of pipe – it doesn’t matter which type of pipe at this time because remember they’re just crossing each other and you’re about to come up with? Cut any weird bends out of the tube before joining them together, making sure that they run smoothly against each other for maximum flow rates You’ll notice that many people leave some space between the two pipes over there.

How to find a sewer line under a concrete slab in 4 easy steps?

How to install a wall trap (a U-shaped bend) with a rigid 4 inch ABS or PVC pipe?

A wall trap is one of the most basic plumbing functions, and it’s designed to allow for either a three-way or four-way division of water flow without having to use a joint.

A U-shaped bend can be installed in a wall using rigid 4-inch diameter ABS or PVC pipe by drilling two 3 or 8-inch holes about an inch from the centerline on both sides, coupling them with a wooden plug that needs to be at least 2.0 inches long (preferably longer).

Then insert both ends simultaneously into their respective drilled hole orientation until the plug snaps securely in place, measuring for appropriate length adjustable PVC threaded nipples which are inserted from either direction and secured tightly from inside with expansion screw plugs.

Villa sport: Know all about Villa Sports; From how they maintain to how you will feel

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button